Home
>> Products
>> MITSUBISHI
>> FX series PLC
>> FX all modules and accessories
>> FX all accessories
>> FX2C-I/O-CON2 Connector
FX2C-I/O-CON2 Connector
MITSUBISHI FX2C-I/O-CON2 Manual And Instructions
FX2C-I/O-CON2 datasheetPDF datasheet
MITSUBISHI FX2C-I/O-CON2 Product information and technical parameters：
Brand: MITSUBISHI
Name: Connector
Model: FX2C-I/O-CON2
Needle number: 40.
Specification: Cable flat cable connector, supporting 2 sets.
...More relevant models >>>>
FX2C-I/O-CON2 datasheetPDF datasheet
MITSUBISHI FX2C-I/O-CON2 Product information and technical parameters：
Brand: MITSUBISHI
Name: Connector
Model: FX2C-I/O-CON2
Needle number: 40.
Specification: Cable flat cable connector, supporting 2 sets.
Protocol: SLMP, TCP/IP, UDP.
Communication mode: full duplex / half duplex.
At the same time can open a few: 4 connection.
Weight: 0.3kg.
Connect PLC FX3U/FX3UC to Ethernet.
Support fixed buffer storage, communication connection MELSOFT, through the MC communication protocol, e-mail messages.
When connected to the MELSOFT, through the Works2 PLC can achieve the remote maintenance of GX program FX2C-I/O-CON2 FX2C-I/O-CON2
Connecting FX3UC, FX3GC requires FX2NC-CNV-IF or FX3UC-IPS-5V. Total input and output points: 48 points.
Input points: 24 points.
Output points: 24 points.
Output type: relay output.
Power supply voltage: AC100-240V.
Input signal voltage: AC100V.
8K capacity of the RAM memory, the maximum can be extended to 16K FX2C-I/O-CON2.
CPU arithmetic processing speed of 0.08 S/ basic instructions.
On the right side of the FX2N series can be connected to the input and output expansion modules and special function modules.
The basic unit is built in the 2 axis independent maximum 20kHz positioning function (transistor output type).
Quick disconnect the terminal block, which adopts excellent maintainability to quickly disconnect the terminal blocks, even if the cable is then replaced by the cable FX2C-I/O-CON2.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application of the continuous scan time.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).
Note recording function, Component annotation can be recorded in the program register.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy too operate FX2C-I/O-CON2.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program. Function: RS-232C communiication FX2C-I/O-CON2.
CPU module connected to the front of the expansion function of the substrate.
The front of the CPU module can be connected to 1 units at most.
Communication mode: full duplex / half duplex.
At the same time can open a few: 4 connection.
Weight: 0.3kg.
Connect PLC FX3U/FX3UC to Ethernet.
Support fixed buffer storage, communication connection MELSOFT, through the MC communication protocol, e-mail messages.
When connected to the MELSOFT, through the Works2 PLC can achieve the remote maintenance of GX program FX2C-I/O-CON2 FX2C-I/O-CON2
Connecting FX3UC, FX3GC requires FX2NC-CNV-IF or FX3UC-IPS-5V. Total input and output points: 48 points.
Input points: 24 points.
Output points: 24 points.
Output type: relay output.
Power supply voltage: AC100-240V.
Input signal voltage: AC100V.
8K capacity of the RAM memory, the maximum can be extended to 16K FX2C-I/O-CON2.
CPU arithmetic processing speed of 0.08 S/ basic instructions.
On the right side of the FX2N series can be connected to the input and output expansion modules and special function modules.
The basic unit is built in the 2 axis independent maximum 20kHz positioning function (transistor output type).
Quick disconnect the terminal block, which adopts excellent maintainability to quickly disconnect the terminal blocks, even if the cable is then replaced by the cable FX2C-I/O-CON2.
Clock function and hour meter function, all of the PLC FX2N has a real-time clock standard.
Continuous scanning function, to define the operation cycle for the application of the continuous scan time.
Input filter adjustment function, you can use the input filter to smooth the input signal (in the basic unit x000 to x017).
Note recording function, Component annotation can be recorded in the program register.
Online program editor, online change the program will not lose the working hours or stop production operation.
RUN/STOP switch, running on panel / stop switch easy too operate FX2C-I/O-CON2.
Remote maintenance, remote programming software can monitor, upload or uninstall programs and data via modem communications
Password protection, using a eight digit password to protect your program. Function: RS-232C communiication FX2C-I/O-CON2.
CPU module connected to the front of the expansion function of the substrate.
The front of the CPU module can be connected to 1 units at most.
...More relevant models >>>>
Last one: 
next one: Related download