Home
>> Products
>> MITSUBISHI
>> L series PLC
>> Branch/Extension module
>> LC10E-CM Extension cable
LC10E-CM Extension cable
MITSUBISHI LC10E-CM Manual And Instructions
LC10E-CM datasheetPDF datasheet
MITSUBISHI LC10E-CM Product information and technical parameters：
Brand: MITSUBISHI
Name: Extension cable
Model: LC10E-CM
Cable length: 1.0m.
Weight: 0.23kg.
Definition 1: conductor by one or a plurality of mutually insulated and insulating protective layer made of,
A conductor of electricity or information from one place to another.
Definition 2: usually by a few or several groups (each with at least two wires) cable rope twisted the similar,
Each group of wires are insulated from each other, and are often twisted around a center,
The entire outer bread has a highly insulated cover.
The cable has the characteristics of internal power and external insulation.
...More relevant models >>>>
LC10E-CM datasheetPDF datasheet
MITSUBISHI LC10E-CM Product information and technical parameters：
Brand: MITSUBISHI
Name: Extension cable
Model: LC10E-CM
Cable length: 1.0m.
Weight: 0.23kg.
Definition 1: conductor by one or a plurality of mutually insulated and insulating protective layer made of,
A conductor of electricity or information from one place to another.
Definition 2: usually by a few or several groups (each with at least two wires) cable rope twisted the similar,
Each group of wires are insulated from each other, and are often twisted around a center,
The entire outer bread has a highly insulated cover.
The cable has the characteristics of internal power and external insulation.
Convert connectors to e-CON.Output points: 8 points (independent of all points).
Rated output voltage: DC24V/AC240V.
Rated open and close current: 2A/1 point.
Public side mode: no public side (all points of independent contact).
Input / output occupied points: 16 points (I/O distribution: output 16 points) LC10E-CM.
External wiring connection: 18 point terminal.
The switch input and output module is a device which can collect the input / output of the switch signal,
Digital I/O modules are often called LC10E-CM
The switch signal is collected to the computer or the computer to send the relevant instructions through the RS-485 bus to control the switch of the switch,
Can also be carried out through the RS-485 bus communication,
Remote control switch LC10E-CM.
Communication protocol is a standard Modbus protocol or custom protocol. Can be isolated from the output of the programmable controller, the a/b/c contact relay, SSR, Tr output.Can be isolated from the output of the programmable controller, the a/b/c contact relay, SSR, Tr output.Convert connectors to fast connectors.
According to the location of the connection equipment distribution module LC10E-CM. Can be isolated from the output of the programmable controller, the a/b/c contact relay, SSR, Tr output.Input and output (DC/ differential).
Input points: 12 points (DC5V/DC24V/ differential universal).
Pulse input speed: the highest pulse/s 8M (2MHz).
Output points: 8 points (DC5V ~ DC24V) 6 points (differential).
Pulse output speed: the highest pulse/s 8M (2MHz).
High speed and stable input / output response
The high speed response can be achieved without the CPU module''s operation and bus performance,
Stable input and output response through hardware processing.
LD40PD01 is equipped with an external input and output interface and FPGA,
Therefore, high speed control can be realized without the influence of the scanning time of the CPU module and the bus performance (the input and output response time of the s instruction is realized).
Can achieve stable input and output response (proocessing time of the deviation of the ns level) LC10E-CM.
Through the intuitive tools for FPGA settings.
In the FPGA design process can be omitted in the past must be designed to deal with (HDL description, logic synthesis and time verification),
Reeduce working hours LC10E-CM. After receiving the product can be used immediately to verify the use of special tools, can significantly shorten the design time.
Rated output voltage: DC24V/AC240V.
Rated open and close current: 2A/1 point.
Public side mode: no public side (all points of independent contact).
Input / output occupied points: 16 points (I/O distribution: output 16 points) LC10E-CM.
External wiring connection: 18 point terminal.
The switch input and output module is a device which can collect the input / output of the switch signal,
Digital I/O modules are often called LC10E-CM
The switch signal is collected to the computer or the computer to send the relevant instructions through the RS-485 bus to control the switch of the switch,
Can also be carried out through the RS-485 bus communication,
Remote control switch LC10E-CM.
Communication protocol is a standard Modbus protocol or custom protocol. Can be isolated from the output of the programmable controller, the a/b/c contact relay, SSR, Tr output.Can be isolated from the output of the programmable controller, the a/b/c contact relay, SSR, Tr output.Convert connectors to fast connectors.
According to the location of the connection equipment distribution module LC10E-CM. Can be isolated from the output of the programmable controller, the a/b/c contact relay, SSR, Tr output.Input and output (DC/ differential).
Input points: 12 points (DC5V/DC24V/ differential universal).
Pulse input speed: the highest pulse/s 8M (2MHz).
Output points: 8 points (DC5V ~ DC24V) 6 points (differential).
Pulse output speed: the highest pulse/s 8M (2MHz).
High speed and stable input / output response
The high speed response can be achieved without the CPU module''s operation and bus performance,
Stable input and output response through hardware processing.
LD40PD01 is equipped with an external input and output interface and FPGA,
Therefore, high speed control can be realized without the influence of the scanning time of the CPU module and the bus performance (the input and output response time of the s instruction is realized).
Can achieve stable input and output response (proocessing time of the deviation of the ns level) LC10E-CM.
Through the intuitive tools for FPGA settings.
In the FPGA design process can be omitted in the past must be designed to deal with (HDL description, logic synthesis and time verification),
Reeduce working hours LC10E-CM. After receiving the product can be used immediately to verify the use of special tools, can significantly shorten the design time.
...More relevant models >>>>
Last one: 
next one: Related download