Home
>> Products
>> MITSUBISHI
>> Servo driver/Servo motor
>> MR-J3 series
>> MR-J3 amplifier
>> MR-J3-350B4-RJ004 Suitable for linear servo motor drive
MR-J3-350B4-RJ004 Suitable for linear servo motor drive
MITSUBISHI MR-J3-350B4-RJ004 Manual And Instructions
MR-J3-350B4-RJ004 datasheetPDF datasheet
MITSUBISHI MR-J3-350B4-RJ004 Product information and technical parameters：
Brand: MITSUBISHI
Name: Suitable for linear servo motor drive
Model: MR-J3-350B4-RJ004
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 3.5kw.
Interface type: SSCNET type III fiber communication.
Special specification: suitable for linear servo motor.
Power specification: three phase AC400V.
More advanced real-time automatic tuning by setting response values,
Including the position gain and the gain of speed, all the gain can be adjusted automatically.
32 segment response level can be set.
Advanced vibration suppression control.
An optimal vibration control filter value is automatically set by the automatic tuning function to effectively suppress the vibration of the 100Hz frequency that occurs when the driving part stops.
The automatic tuning function can effectively restrain the vibration of the end of the mechanical arm and reduce the residual vibration in the machine.
...More relevant models >>>>
MR-J3-350B4-RJ004 datasheetPDF datasheet
MITSUBISHI MR-J3-350B4-RJ004 Product information and technical parameters：
Brand: MITSUBISHI
Name: Suitable for linear servo motor drive
Model: MR-J3-350B4-RJ004
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 3.5kw.
Interface type: SSCNET type III fiber communication.
Special specification: suitable for linear servo motor.
Power specification: three phase AC400V.
More advanced real-time automatic tuning by setting response values,
Including the position gain and the gain of speed, all the gain can be adjusted automatically.
32 segment response level can be set.
Advanced vibration suppression control.
An optimal vibration control filter value is automatically set by the automatic tuning function to effectively suppress the vibration of the 100Hz frequency that occurs when the driving part stops.
The automatic tuning function can effectively restrain the vibration of the end of the mechanical arm and reduce the residual vibration in the machine.
The length of the line: 5M.
IP level: IP65.
Direct type.
The cable is not shielded.
Bending life: standard.
Connector kit for motor electromagnetic brake.
Cable for electromagnetic brake, for HF-KP/HF-MP series (motor shaft with side extraction). MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series MR-J3-350B4-RJ004.
Rated output: 1.0kw.
Interface type: SSCNET type III fiber communication MR-J3-350B4-RJ004
Special features: integrated driver security.
Power specification: three phase AC400V.
STO function as a security feature is added to the SSCNET III fiber communication type servo amplifier.
By using the STO function, the electromagnetic contactor used in the past to prevent the motor from accidentally starting is no longer needed MR-J3-350B4-RJ004.
SS1 functions can be realized by using the MR-J3-D05 security logic unit.
MR-J3-BS uses a full closed loop control system.
Compatibility with MR-J3-B.
MR-J3-BS installation, wiring and connectors are the same as the MR-J3-B, so do not change the existing connection will be easy to MR-J3-B
Change to MR-J3-BS.
Security functions are connected to the CN8 interface through an external security circuit to increase the MR-J3-BS driver security MR-J3-350B4-RJ004.
Compatible full closed loop control system.
MR-J3-BS has a full closed loop control system version. Drive: MR-H_ACN series SSC-NET compatible AC servo.
Rated output: 0.6KW.
The servo controller can easily transfer the operation module and the field bus module through the automation interface,
At the same time using different fieldbus modules to achieve different control modes (RS485, RS232, optical fiber, InterBus, ProfiBus),
And the control mode of general inverter is single.
The servo controller is directly connected with a rotary transformer or an encoder, which forms a closed loop of speed and displacement control.
The general inverter can only form an open loop control system.
Servo controller of the control parameters (such as steady-state accuracy and dynamic performance) is better than the general inverter. Motor series: low inertia, medium and small capacity.
Using a serial absolute / incremental encoder.
Rated output power: 0.2kw.
Rated speed: 3000rpm.
With the brake: without.
Shaft end: straight shaft.
Comparison of single phase induction motor and servo motor.
The working principle of the AC servo motor is similar to that of the single phase induction motor,
But the rotor resistance of the former is much larger than that of the latter,
So the servo motor is compared with the single machine asynchronous motor,
There are three notable features:
1, large starting torque.
2, a wide rangee of operation MR-J3-350B4-RJ004.
3, no rotation phenomenon.
AC servo motor running smoothly, low noise.
But the control characteristic is non-linear, and because the rotor resistance is big, the loss is big, the efficiency is low,
Therefore, comparred with the same capacity DC servo motor, the volume is large and the weight is heavy,
So it is only suitable for 0 MR-J3-350B4-RJ004. 5-100W small power control system.
IP level: IP65.
Direct type.
The cable is not shielded.
Bending life: standard.
Connector kit for motor electromagnetic brake.
Cable for electromagnetic brake, for HF-KP/HF-MP series (motor shaft with side extraction). MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series MR-J3-350B4-RJ004.
Rated output: 1.0kw.
Interface type: SSCNET type III fiber communication MR-J3-350B4-RJ004
Special features: integrated driver security.
Power specification: three phase AC400V.
STO function as a security feature is added to the SSCNET III fiber communication type servo amplifier.
By using the STO function, the electromagnetic contactor used in the past to prevent the motor from accidentally starting is no longer needed MR-J3-350B4-RJ004.
SS1 functions can be realized by using the MR-J3-D05 security logic unit.
MR-J3-BS uses a full closed loop control system.
Compatibility with MR-J3-B.
MR-J3-BS installation, wiring and connectors are the same as the MR-J3-B, so do not change the existing connection will be easy to MR-J3-B
Change to MR-J3-BS.
Security functions are connected to the CN8 interface through an external security circuit to increase the MR-J3-BS driver security MR-J3-350B4-RJ004.
Compatible full closed loop control system.
MR-J3-BS has a full closed loop control system version. Drive: MR-H_ACN series SSC-NET compatible AC servo.
Rated output: 0.6KW.
The servo controller can easily transfer the operation module and the field bus module through the automation interface,
At the same time using different fieldbus modules to achieve different control modes (RS485, RS232, optical fiber, InterBus, ProfiBus),
And the control mode of general inverter is single.
The servo controller is directly connected with a rotary transformer or an encoder, which forms a closed loop of speed and displacement control.
The general inverter can only form an open loop control system.
Servo controller of the control parameters (such as steady-state accuracy and dynamic performance) is better than the general inverter. Motor series: low inertia, medium and small capacity.
Using a serial absolute / incremental encoder.
Rated output power: 0.2kw.
Rated speed: 3000rpm.
With the brake: without.
Shaft end: straight shaft.
Comparison of single phase induction motor and servo motor.
The working principle of the AC servo motor is similar to that of the single phase induction motor,
But the rotor resistance of the former is much larger than that of the latter,
So the servo motor is compared with the single machine asynchronous motor,
There are three notable features:
1, large starting torque.
2, a wide rangee of operation MR-J3-350B4-RJ004.
3, no rotation phenomenon.
AC servo motor running smoothly, low noise.
But the control characteristic is non-linear, and because the rotor resistance is big, the loss is big, the efficiency is low,
Therefore, comparred with the same capacity DC servo motor, the volume is large and the weight is heavy,
So it is only suitable for 0 MR-J3-350B4-RJ004. 5-100W small power control system.
...More relevant models >>>>
Last one: MITSUBISHI Suitable for linear servo motor drive MR-J3-200B4-RJ004
next one: MITSUBISHI Suitable for linear servo motor drive MR-J3-500B4-RJ004
Related download