MITSUBISHI
Home >> Products >> MITSUBISHI >> Servo driver/Servo motor >> MR-J3 series >> MR-J3 amplifier >> MR-J3-60B-RJ006 Full closed loop control driver

MR-J3-60B-RJ006 Full closed loop control driver

MITSUBISHI MR-J3-60B-RJ006 Manual And Instructions
MR-J3-60B-RJ006 datasheetPDF datasheet
MR-J3-60B-RJ006 INSTRUCTION MANUAL

MITSUBISHI MR-J3-60B-RJ006 Product information and technical parameters:
Brand: MITSUBISHI
Name: Full closed loop control driver
Model: MR-J3-60B-RJ006
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 0.6kw.
Interface type: SSCNET type III fiber communication.
Full closed loop control.
Power specification: single phase AC200V.
High precision and high response location control.
Full closed loop control can be realized by double feedback control method.
Dual feedback control can be performed between the servo motor encoder and the load side encoder.
MR-J3-B-RJ006 can be used in conjunction with a number of manufacturers of linear encoder,
Users can build the system according to their own accuracy requirements. ABS type linear encoder using serial interface,
No need to install the battery on the servo amplifier can easily build the absolute position detection system.
Flexible system configuration.
Can achieve higher load side positioning accuracy!

Type: HA-SE series.
Rated output: 1.0KW.
Rated speed: 2000r/min.
Electromagnetic brake: there.
Control complex, easy to achieve intelligent,
The electronic commutation method is flexible and can be changed by square wave or sine wave.
Motor maintenance free, high efficiency, low operating temperature,
Electromagnetic radiation is very small, long life, can be used in a variety of environments MR-J3-60B-RJ006 MR-J3-60B-RJ006
AC servo motor is brushless motor, which is divided into synchronous and asynchronous motor,
Synchronous machines are commonly used in motion control,
Its power range, you can do a lot of power.
Large inertia, the maximum rotation speed is low, and with the increase of power and rapid reduction.
So it is suitable for the application of low speed and stable operation MR-J3-60B-RJ006.
The rotor of the servo motor is permanent magnet,
Drive controlled U/V/W three phase electric electromagnetic field,
The rotor rotates under the action of the magnetic field,
At the same time the motor comes with the encoder feedback signal to the drive,
According to the feedback value and the target value, the driver is compared,
Adjust the rotor rotation angle MR-J3-60B-RJ006.
The accuracy of the servo motor is determined by the accuracy of the encoder. Servo motor series: medium inertia, small capacity.
Rated output: 0.85kw.
Rated speed: 1000r/min.
Electromagnetic brake: No.
Power supply: 200V.
Stable driving of medium capacity and medium inertia type products.
Through the optimization of structural design, to achieve the minimum length of the industry.
High speed & high torque. Shorten the positioning time, achieve high-speed equipment.
Reducing the electric torque ripple.
Through the combination of the optimal number of the motor and the slot number, the torque ripple is greatly reduced,
To further realize the smooth constant speed device.
Improve the environmental performance of HG-SR, HG-JR series of products using IP67. Drive unit.
MITSUBISHI universal AC servo amplifier MELSERVO-J4 series.
Rated output: 30kw.
Interface: universal type.
Power supply: three phase AC400V.
Support position control, speed control, torque control.
Position control to follow the position instructions.
Whenn the control is inserted, the position control is performed MR-J3-60B-RJ006.
Speed control follows the speed command to control the speed within a certain range.
Torque control to follow the torque command to control the stable torque.
Function of switching amplitude MR-J3-60B-RJ006. The increase in the process of switching and stopping,
And in the operation of the use of the switching signal, switching growth.


...More relevant models >>>>