MR-J60A Servo driver
MITSUBISHI MR-J60A Manual And Instructions
MR-J60A datasheetPDF datasheet
MITSUBISHI MR-J60A Product information and technical parameters：
Brand: MITSUBISHI
Name: Servo driver
Model: MR-J60A
Type: MR-J series.
Rated output: 0.6KW.
Applicable motor series: HA-FF, HA-SE.
Voltage: three phase AC220V.
It is very helpful to improve the stability of the low speed control of the servo motor.
But there is no direct effect to improve the accuracy of position control.
There are, of course, software compensation that is similar to pitch compensation,
Can improve the physical resolution of the single lap, so as to improve the accuracy of positioning control.
This can be effectively used in the use of the robot control of the indexing table.
It is also because of the application of splicing technology,
The rotary encoder will be more widely used in the high precision servo control in the harsh environment.
The use of rotary encoder with 224/ in the servo motor has been used in the servo motor.
Encoder serial communication system, the communication frequency can only be limited to 10M.
...More relevant models >>>>
MR-J60A datasheetPDF datasheet
MITSUBISHI MR-J60A Product information and technical parameters：
Brand: MITSUBISHI
Name: Servo driver
Model: MR-J60A
Type: MR-J series.
Rated output: 0.6KW.
Applicable motor series: HA-FF, HA-SE.
Voltage: three phase AC220V.
It is very helpful to improve the stability of the low speed control of the servo motor.
But there is no direct effect to improve the accuracy of position control.
There are, of course, software compensation that is similar to pitch compensation,
Can improve the physical resolution of the single lap, so as to improve the accuracy of positioning control.
This can be effectively used in the use of the robot control of the indexing table.
It is also because of the application of splicing technology,
The rotary encoder will be more widely used in the high precision servo control in the harsh environment.
The use of rotary encoder with 224/ in the servo motor has been used in the servo motor.
Encoder serial communication system, the communication frequency can only be limited to 10M.
Fiber length: 1 meters.
SSCNET III cables (standard optical fiber used in control cabinet).
Joints for CN1A and CN1B. Drive: MR-H_ACN series SSC-NET compatible AC servo.
Rated output: 11KW.
The servo controller can easily transfer the operation module and the field bus module through the automation interface,
At the same time using different fieldbus modules to achieve different control modes (RS485, RS232, optical fiber, InterBus, ProfiBus),
And the control mode of general inverter is single MR-J60A MR-J60A
The servo controller is directly connected with a rotary transformer or an encoder, which forms a closed loop of speed and displacement control.
The general inverter can only form an open loop control system MR-J60A.
Servo controller of the control parameters (such as steady-state accuracy and dynamic performance) is better than the general inverter. MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 0.2kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: single phase AC100V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller MR-J60A.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitorinng and other operations MR-J60A.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation MR-J60A.
When the two stations are occupied, the speed can be set directly by the remote register.
SSCNET III cables (standard optical fiber used in control cabinet).
Joints for CN1A and CN1B. Drive: MR-H_ACN series SSC-NET compatible AC servo.
Rated output: 11KW.
The servo controller can easily transfer the operation module and the field bus module through the automation interface,
At the same time using different fieldbus modules to achieve different control modes (RS485, RS232, optical fiber, InterBus, ProfiBus),
And the control mode of general inverter is single MR-J60A MR-J60A
The servo controller is directly connected with a rotary transformer or an encoder, which forms a closed loop of speed and displacement control.
The general inverter can only form an open loop control system MR-J60A.
Servo controller of the control parameters (such as steady-state accuracy and dynamic performance) is better than the general inverter. MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 0.2kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: single phase AC100V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller MR-J60A.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitorinng and other operations MR-J60A.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation MR-J60A.
When the two stations are occupied, the speed can be set directly by the remote register.
...More relevant models >>>>
Last one: 
next one: Related download