MITSUBISHI
Home >> Products >> MITSUBISHI >> Inverter >> FR-F800 series inverter >> FR-F840 inverter 3 phase 400V >> FR-F840-04810-2-60 Three phase 400V grade frequency converter

FR-F840-04810-2-60 Three phase 400V grade frequency converter

MITSUBISHI FR-F840-04810-2-60 Manual And Instructions
FR-F840-04810-2-60 datasheetPDF datasheet

MITSUBISHI FR-F840-04810-2-60 Product information and technical parameters:
Brand: MITSUBISHI
Name: Three phase 400V grade frequency converter
Model: FR-F840-04810-2-60
MITSUBISHI inverter series: FR-F840.
Voltage level: three phase 400V.
Power: 220kw.
SLD converter rated current: 481A.
Structure and function: Standard model.
Type: CA.
Substrate coating: have.
The motor efficiency is not changed in the previous optimal excitation control,
At the same time, the newly developed advanced optimal excitation control can obtain larger torque at startup.
No need to adjust the parameters (plus deceleration time or torque, etc.), in a short time to speed up to a certain speed,
Can be carried out to maximize the efficiency of energy-saving drive motor.
The automatic tuning function of the loop constant of the motor is not consistent with the constant of the motor, the motor of other manufacturers, and the length of wiring is too long,
Optimum operating characteristic drive motor.
In the state of the sensor can not only drive the high efficiency and energy saving motor and PM motor (MM-EFS), but also can drive other companies induction motor and PM motor (permanent magnet synchronous motor).
Other manufacturers of induction motors, can also be automatically tuned to achieve the best excitation control, thus expanding the use of energy saving.

Power: 7.5kw.
Voltage: 200V.
There are 100% braking torque output in continuous regeneration, which can correspond to the continuous regeneration operation of the pipeline control.
There is no need to install the braking unit for each frequency converter, which can reduce the comprehensive space and reduce the comprehensive cost FR-F840-04810-2-60.
Renewable energy can be used for other frequency converter, excess energy back to the grid, to achieve energy saving FR-F840-04810-2-60 MITSUBISHI inverter FR-D740 series.
Voltage level: three phase 400V.
Frequency converter capacity: 0.75KW.
The internal and back of the inverter structure considering the cooling effect, the relationship between the upper and lower ventilation is also important,
Therefore, in order for the type of unit, hanging on the wall to the vertical position, the installation of vertical as possible FR-F840-04810-2-60.
Transducer can be used to drive a single phase motor? Can single phase power supply be used?
Basically can not be used. For a single phase motor with governor switch, the auxiliary winding will be burnt when the speed is below the operating point;
For the capacitor start or capacitor operation mode, the capacitor explosion will be induced FR-F840-04810-2-60.
The inverter power supply is usually 3, but the capacity for small, single-phase power is also useful functioning aircraft. MITSUBISHI inverter FR-A740 series.
Voltage level: 3 phase 400V.
Frequency converter capacity: 2.2KW.
FR-A700 converter products are suitable for all kinds of high load requirements of the equipment.
Such as lifting, lift, printing and dyeing, printing and dyeing, material coiling and other general occasions.
High level driving performance.
Unique sensorless vector control mode,
A wide variety of mechanical equipment can be opperated at high precision in the super low speed region without the need of the encoder FR-F840-04810-2-60.
With torque control mode,
And in the speed control mode can use the torque limit function.
With vector control function (with encoder),
Frequuency converter can achieve position control and fast response, high precision speed control (zero speed control, servo lock, etc FR-F840-04810-2-60. ) and torque control.


...More relevant models >>>>